1, piston pump Rationale: By reciprocating the piston inside the cylinder, the cylinder volume is repeatedly changed to suck and discharge the fluid. 2, reciprocating pump Working principle: the use of eccentric shaft rotation through the connecting rod device to drive the movement of the piston, the rotation of the shaft into piston reciprocating motion. Pistons continue reciprocating motion, the pump suction and water pressure on the continuous process of alternating. Special structure 3, water ring vacuum pump How it works: Water ring vacuum pump impeller eccentric mounted in a cylindrical pump housing. Pump into a certain amount of water. When the impeller rotates, the water is thrown to the pump housing to form a water ring whose inner surface is tangent to the impeller hub. As the pump housing and the impeller is not the heart, the right half of the hub and the water ring between the intake space 4 gradually expanded, thus forming a vacuum, the gas into the pump into the intake space through the gas pipe. Then the gas enters the left half and the pressure is increased due to the gradual compression of the volume between the hub rings, so that the gas is discharged to the outside of the pump through the exhaust space and the exhaust pipe. 4, Roots vacuum pump How Does It Work? Roots pumps work like Roots blowers. Due to the constant rotation of the rotor, the drawn gas is sucked into the space v0 between the rotor and the pump housing through the air inlet and then discharged through the air outlet. Since inhaled v0 space is completely closed state, so the gas in the pump chamber is not compressed and expanded. However, when the top of the rotor turns over the edge of the exhaust port, when the v0 space communicates with the exhaust side, since the pressure of the exhaust side gas is higher, a part of the gas bounces back into the space v0 to make the gas pressure suddenly increase. When the rotor continues to rotate, the gas is discharged outside the pump. In general, Roots pumps have the following features: ◠in a wide range of pressure has a larger pumping speed; ◠start fast, can work immediately; ◠insensitive to the dust and water vapor contained in the gas to be evacuated; ◠The rotor does not have to be lubricated and there is no oil in the pump chamber. ◠small vibration, rotor balancing conditions are better, there is no exhaust valve; ◠drive power is small, mechanical friction loss is small; ◠compact structure, small footprint; ◠operation and maintenance costs low. Therefore, Roots pumps in the metallurgical, petrochemical, paper, food, electronics industry sector has been widely used. 5, rotary vane vacuum pump How it works: Rotary vane vacuum pump (referred to as rotary vane pump) is a seal-type mechanical vacuum pump. The working pressure range of 101325 ~ 1.33 × 10-2 (Pa) belongs to the low vacuum pump. It can be used alone or as a foreline pump for other high-vacuum or ultra-high vacuum pumps. It has been widely used in metallurgy, machinery, military, electronics, chemicals, light industry, petroleum and pharmaceutical production and research departments. Rotary vane pump mainly by the pump body, rotor, rotary vane, end caps, springs and other components. A rotator is eccentrically mounted in the cavity of the rotary vane pump, the outer circumference of the rotor is tangent to the inner surface of the pump cavity (both have a small gap), and two rotary vanes with springs are arranged in the rotor slot. Rotation, by centrifugal force and the tension of the spring so that the top of the rotary vane and the inner wall of the pump chamber to maintain contact with the rotor rotation of the rotary vane slide along the wall. The two vanes separate the crescent-shaped space enclosed by the rotor, the pump chamber and the two end caps into A, B and C sections. When the rotor rotates in the direction of the arrow, the volume of the space A communicating with the suction port gradually increases and is in the process of suction. While the volume of the space C communicating with the exhaust port is gradually reduced and is in the process of exhausting. The volume of the central space B is also gradually reduced, is in the process of compression. Since the volume of space A is gradually increased (ie, expanded), the pressure of the gas is decreased and the pressure of the external gas at the inlet of the pump is greater than the pressure in space A, so gas is drawn in. When the space A and the suction port isolated, that is, to the space B position, the gas began to be compressed, the volume gradually reduced, and finally connected to the exhaust port. When the compressed gas exceeds the pressure of the exhaust gas, the exhaust valve is pushed by the compressed gas and the gas is discharged into the atmosphere through the oil layer in the fuel tank. By the continuous operation of the pump, to achieve the purpose of continuous extraction. If the discharge of gas through the airway and into another level (low vacuum level), from the low vacuum stage pumped away, and then by the low vacuum stage after the discharge to the atmosphere, the composition of the two-stage pump. At this time the total compression ratio is borne by two levels, thus increasing the ultimate vacuum. 7, internal gear pump What to pay attention to when running (1) Check if the device has been carefully and completely installed (2) The pressure fluid can only be filled at the minimum capacity ratio through the filter (3) Note the arrow in the direction of rotation (4) Run the pump without load and allow it to run without pressure for a few seconds in order to achieve adequate lubrication (5) Never run the pump without oil (6) If the pump is still running for 20 seconds, check the pump again, and after reaching the operating value, check the tightness of the pipe connection (7) Check the operating temperature 8, external gear pump 9, mud pump 10, gas booster pump (1) a wide range of working pressure, choose different types of pumps available to different pressure areas, Adjust the input pressure The output pressure is adjusted accordingly. Can reach very high pressure, gas 90Mpa (2) A wide range of flow, for all models only 0.1Kg pressure pump will be able to work smoothly, this time to obtain the minimum flow, adjust the intake air flow rate can be obtained after. (3) easy to control, from simple manual control to complete automatic control can meet the requirements. (4) automatic restart, no matter what kind of pressure packing circuit pressure drop will automatically restart to supplement the leakage pressure, keep the loop pressure constant. (5) safe operation, using gas-driven, no arcing and sparks, can be used in hazardous situations. (6) The maximum energy-saving up to 70%, because maintaining pressure does not consume any energy. 11, gas-liquid booster pump working principle The one-way valve controlled by the high-pressure plunger constantly liquid discharge, booster pump outlet pressure and air-driven pressure. When the pressure between the drive section and the output liquid section reaches equilibrium, the booster pump stops operating and consumes no more air. When the output pressure drops or the air-driven pressure increases, the booster pump will automatically start running until it reaches the pressure balance again after the automatic stop. The use of single gas-controlled unbalanced gas distribution valve to achieve automatic reciprocating pump, gas drive part of the pump body made of aluminum. Wetted part of the media according to the different choice of carbon steel or stainless steel, pump full set of seals are imported high-quality products, thus ensuring the performance of gas-liquid booster pump.
Matte Metallic Car Wrap is no bubbles, no fade, slow down aging, preserve the value of your car, not need for waxing , coating, and simple clean, easy to applied and easy removed, change car color not damage car paint, color collocation is more independent, low daily maintenance cost.
Material: PVC
Size : 60'' x 59' ( 152CM x 18M )
We are China Origin Factory of Vinyl Vs Vvivid. If you have any question, please feel free to Contact Us.
Matte Metallic Car Wrap,Vinyl Blue,Custom Matte Metallic Car Wrap,Vinyl Boat Lettering Guangzhou Carlori Co., Ltd , https://www.carloriauto.com
The working principle of these 11 pumps you know what
ã€Print】 ã€Close】